General

Cleaning

Specialized Tools

Dismantling

Rebuilding

Dropping the engine

Flywheel Removal

Splitting the Casings

Oil Seals: Flywheel Side

Oil Seals: Clutch Side

Shift Cross Replacement

Bearings

Installing a Crank

Clutch Overview

Clutch Removal

Clutch Rebuilding

Home

[Small frame Vespa clutch]

The clutch on all large frame Vespas is located on the rear wheel side of the crankshaft. There is an access cover which can be removed while the engine is still in the bike. Although the pictures are all from a P200E, these instructions will be correct for all large frame bikes after the GS150 & GS160. To remove the clutch you will need:

• A 10mm socket and driver (later PX200 models use an 8mm socket)
• A 13mm socket and driver for the rear wheel rim.
• A clutch nut tool.
• A new castelated nut and tabbed retaining washer (from your scooter shop).
• A small flathead screwdriver.
• A small pair of needle nose pliers.
• Something to support the rear of the bike like a milk crate or jack stand.

If you are going to replace the clutch plates you'll also need:

• A pint of SAE 30 transmission oil.
• 3 new cork clutch plates.
• New springs (might as well)!
• A clutch compressor tool or a home made version from typical hardware store items.

 

The first step is to get the bike up on the main stand and put something like a milk crate, 2x4, or a jack stand between the tail of the frame and the ground. You need something just long enough to allow the rear wheel to spin freely. On a P200 the plastic tail bumper is a snap fit and can be removed before taking the weight of the bike on the tail. Remove the five 13mm wheel rim nuts on the right side of the rear tire (battery or glovebox side) to remove the rim.

 

Once this is done the rear rim should come loose. The rear wheel will only come out of the frame one way. You have to dislodge it from the rear hub, and move it backwards towards the tail.

 

With the jack stand in place and the bike still on the center stand it is easier to get the clearance to get at the clutch cover. The cover is located just above the rear wheel hub and has a small arm and spring coming out of the bottom of it.

 

If your bike has seen some good use your clutch cover will look somewhat like the one pictured above. It is a good idea to run a rag over the area where the clutch cover seals against the crankcase to make sure that no grime falls into the transmission. To remove the clutch cover you'll need a 10mm socket and driver. Do not confuse the end of the transmission input shaft as one of the bolts. It is located right on the side of the clutch cover and is much larger than 10mm. It is not necessary to disconnect the clutch cable from the clutch arm unless you need to replace or completely remove the clutch cover. Once the three bolts (arrowed above) are removed the clutch cover will come off with a small pull on the clutch arm, away from the casing. There is a small brass plunger which may fall out so be sure to save it for later.

 

Above is a shot of the clutch with the cover removed. The clutch is actuated by the small brass plunger (which may or may not have fallen out of the clutch cover) pushing on the center plate of the bell housing. The center plate has a small bent piece of wire which secures it over the clutch retaining washer and nut. To remove it use a pair of needle nose pliers to push both ends toward the center of the plate.

 

With the center plate removed, the nut and retaining washer are now clearly visible. The way the retaining washer works is that it has many metal tabs around the perimeter, and a single tab in the center which slides into a slot in the crankshaft. When the castelated nut is torqued down, one of the tabs will usually line up with a 'valley', and is bent into the lower part of the castelated nut. This stops the nut from loosening under turning from the crank and/or clutch.

 

Firstly, if the end of your crank looks anything like the one pictured above, you may want to consider a more comprehensive rebuild. These pictures were taken with an old crank/clutch combination out of the bike to show the detail of the nut/washer relationship as it is very important. In the first picture above, the red arrow above shows the tab bent over in the 'valley' of the castelated nut. You can also see the slot in the crank end which forces the washer to turn with the crank rather than with the nut. The green dashed line is there to show how to orient the clutch before you remove it. There is a woodruff key set in the crank end which is hidden but can drop into the gearbox unless it is facing upwards. The green line should face directly up even though it is off by 15 degrees or so in these shots.

The second picture above shows the tab bent back in line with all the others which will allow the clutch nut to be loosened and removed. I use a small flat head screwdriver to get under the tab and pry it back. Before loosening and removing the clutch nut the clutch bell has to be stopped from turning. On most bikes the clutch will not need anything more than a rag and a tough grip by yourself or a helper. If it still wants to turn with the crank here are a few things you should NOT do:

• Lock the flywheel with something to stop it turning. This could warp the crank because one side is trying to turn while the other is stationary this and could put harmful force on the big end pin.
• Jam a screwdriver in between the clutch bell and the primary drive gear which is visible through the space around the clutch bell. If you chip a gear tooth it will mean a full rebuild.
• Jam anything through the spark plug hole to lock the engine by stopping the piston from traveling upwards.

Of course Vespa has a tool which locks the clutch in place and while you could make one, I have found that with a little care, the following method works quite well (thanks Matthew). I thread the lower 10mm bolt almost all the way back into the casing by hand and get a small flathead screwdriver to wedge into one of the clutch bell housing slots. If the screwdriver is long enough the handle will then jamb on the swingarm as you increase the pressure on the clutch nut.

 

This system seems to work well and doesn't elongate or put a slot in the clutch bell housing because the force loosening the clutch nut is slowly applied Please note that this is not really the correct way to do it but it has worked for me on the few times a rag and a strong grip hasn't been successful. Try it at your own risk...

 

Now use the clutch nut removal tool and a driver to remove the clutch nut. This should always be replaced along with the retaining washer as they are cheap and the more times they are used the more rounded of the nut edges get which will make it harder to loosen in the future. When the clutch nut is removed the retaining washer can slide out of the recess. In the second picture above you can now see the woodruff key slot in the clutch drive assembly, which must face directly up before pulling the clutch off the crank.

 

The clutch can now be pulled free using only your hands. If it is stubborn do nut use screwdrivers to lever it off as they may damage the sealing face of the clutch casing opening. The clutch has been removed on the shot above. Since this clutch system was used for so many years, not all Vespas will look like this, but they will look similar. This shot is from an autolube P200E. If you are interested, the yellow arrow shows the oil metering drive, the red shows the end of the crank. and the blue shows the large helical cut primary drive gear.

 

Once removed be sure to either remove the woodruff key (red arrow) in the crank or tape it in place. There is nothing worse than one falling into the gearbox making an hour long clutch replacement turn into a full rebuild.